Andy's 91' 80q

Document and share your build!

Re: Andy's 91' 80q

Postby rennenmsports » Sat Mar 10, 2018 3:22 pm

968AB23F-6416-41B3-A194-F074B96EE336.jpeg
968AB23F-6416-41B3-A194-F074B96EE336.jpeg (1.81 MiB) Viewed 2231 times

Starting to make the Home Depot front clip :lol:
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby PRY4SNO » Sun Mar 11, 2018 12:40 am

That looks the business for a DIY project. Can't count the times I've said to the woman, "if only I had a welder."

Why'd you cut the snub mount?
Find me on Instagram @pry4sno

|| 2010 Golf Sportwagen TDI /// Farmenwagen
|| 1992 80 quattro 20v /// Eventual AAN'd Winter Sled
|| 1990 Coupe quattro /// Because Racecar

|| Spare parts for sale
User avatar
PRY4SNO
 
Posts: 2033
Joined: Mar 3, 2013
Location: Edmonton, AB

Re: Andy's 91' 80q

Postby rennenmsports » Sun Mar 11, 2018 9:59 am

A welder is very nice to have yes. I don’t know what I would do without it. Once u get one it’s like a smart phone. U can’t live without it! I cut the snub mount back to put the intercooler further in and up. It looks like this
image.jpg
image.jpg (1.41 MiB) Viewed 2212 times
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Sun Mar 11, 2018 10:13 am

I was trying to get the factory US bumper to fit but nope :huh: the aluminum bumper frame does though. Barely. I’m going to weld the bumper shocks in a fixed position so it doesn’t hit the cooler in a minor fender bender. Anyone have a banged up S2/RS2 bumper for sale? My friendly neighborhood HOA might complain soon. Hahahaha
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby mrdeye » Sun Mar 11, 2018 2:02 pm

Nice! :beer:
Matt
Daily driver: '01 Toyota 4Runner
Project car: '84 Audi Coupe GT
Previous cars:
'95 S6 Avant, '87 5K TQ, '95 VW Golf, '84 VW Jetta turbo diesel, '84 VW GTI
mrdeye
 
Posts: 59
Joined: Nov 13, 2016
Location: Colorado

Re: Andy's 91' 80q

Postby rennenmsports » Fri Mar 16, 2018 7:42 pm

I drilled a hole in the side of the bumper shocks so I could weld them in a fixed position to keep the aluminum bumper frame from hitting the intercooler in the event of a fender bender. God forbid. But I’m glad that they didn’t blow up in my face when I drilled into them. Hahahaha.
AC4EFFB3-3F2D-45B6-8AA2-27A1047AE516.jpeg
AC4EFFB3-3F2D-45B6-8AA2-27A1047AE516.jpeg (1.09 MiB) Viewed 2140 times
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Fri Mar 23, 2018 7:53 pm

16067258-51DA-4487-8B98-9213DBA10C9D.jpeg
16067258-51DA-4487-8B98-9213DBA10C9D.jpeg (1.21 MiB) Viewed 2054 times
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby DE80q » Sat Mar 24, 2018 5:49 am

Having to have up the bumper was the reason I went with a standard universal size intercooler and modified it to fit. I also removed a large protion of the aluminum bumper to make it fit.
"If you cant find one, make one!"


91 Audi 80q -10vt project
07 Mitsubishi Raider (Dakota in disguise)
DE80q
 
Posts: 2130
Joined: Mar 4, 2013
Location: York PA 17403

Re: Andy's 91' 80q

Postby rennenmsports » Sat Mar 24, 2018 7:41 am

Now that I’m looking at it. :huh: I should move it up. Here is a picture of the cooler with about 3/16” clearance on each side. Front and back.
6E0329B3-46C2-4266-9BF5-605DE772FC88.jpeg
6E0329B3-46C2-4266-9BF5-605DE772FC88.jpeg (1.68 MiB) Viewed 2039 times
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Sat Apr 21, 2018 8:12 am

Well its still in the same spot. I decided to leave it there due to air flow and the fact that I don't have an S2/RS2 front bumper. What I have been doing is hooking all the wiring up. Since I don't want to cut the harness and due to the intake manifold setup I need to extend the TPS and IAT. Everything went fine except there is no such thing as a TPS male pin female connector. Mark was able to make one out of plastic :hail: That was awesome!
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Mon Apr 23, 2018 10:42 am

Hahahaha
FD42C8BB-7328-4A87-A1EA-311AE5130FC1.jpeg
FD42C8BB-7328-4A87-A1EA-311AE5130FC1.jpeg (1.29 MiB) Viewed 1034 times
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Wed Apr 25, 2018 5:48 pm

try1.jpg
try1.jpg (1.8 MiB) Viewed 818 times
Last edited by rennenmsports on Sat Apr 28, 2018 8:10 am, edited 1 time in total.
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby ringbearer » Thu Apr 26, 2018 11:50 am

Rubber side down speed racer ;)
User avatar
ringbearer
 
Posts: 1195
Joined: Feb 27, 2013
Location: Nor-Cal

Re: Andy's 91' 80q

Postby rennenmsports » Thu Apr 26, 2018 4:03 pm

ringbearer wrote:Rubber side down speed racer ;)

Huh? Rubber side of what?
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby DE80q » Fri Apr 27, 2018 3:23 am

rennenmsports wrote:
ringbearer wrote:Rubber side down speed racer ;)

Huh? Rubber side of what?

The car :shame:
"If you cant find one, make one!"


91 Audi 80q -10vt project
07 Mitsubishi Raider (Dakota in disguise)
DE80q
 
Posts: 2130
Joined: Mar 4, 2013
Location: York PA 17403

Re: Andy's 91' 80q

Postby rennenmsports » Sat Apr 28, 2018 8:45 pm

:rofl:
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Re: Andy's 91' 80q

Postby ringbearer » Mon Apr 30, 2018 5:36 pm

I just went on a drive and one of the guys had this same car he bought new and now has 330k on it. I think it’s had suspension and brake upgrades but otherwise stock and untouched. He pushed it hard and it did very well, was fun to see.
User avatar
ringbearer
 
Posts: 1195
Joined: Feb 27, 2013
Location: Nor-Cal

Re: Andy's 91' 80q

Postby rennenmsports » Sat May 19, 2018 6:25 pm

B5 fan controller installed
3DFE4F7D-2D86-4C36-B7B5-44FCBB04DCB8.jpeg
3DFE4F7D-2D86-4C36-B7B5-44FCBB04DCB8.jpeg (1.93 MiB) Viewed 110 times
rennenmsports
 
Posts: 56
Joined: Jan 14, 2017

Previous

Return to Projects

Who is online

Users browsing this forum: No registered users and 6 guests