The Project Pad

my2000apb wrote:

a_CQ wrote:She zooms in on you and you can't zoom in on her?!?

That chick's a keeper..

ahahahaha yeah

more pics!!!

HAHA I don't think she would be too happy with me posting her up online like that . Or I totally would, but I gotta respect her wishes hahaha.

As for the IE stuff, I am still waiting to get the goodies. As soon as they show up I will post up some pictures!

extreme90path wrote:

my2000apb wrote:

a_CQ wrote:She zooms in on you and you can't zoom in on her?!?

That chick's a keeper..

ahahahaha yeah

more pics!!!

HAHA I don't think she would be too happy with me posting her up online like that . Or I totally would, but I gotta respect her wishes hahaha.

As for the IE stuff, I am still waiting to get the goodies. As soon as they show up I will post up some pictures!

what if shes wishes to be shown off to your MG buddies?!?!?!

Maybe one of these days I will dig out the pictures of her with the 4kq

:slap: DO IT!!!

I wanna see the both. IE rods and girl

I may order some IE's this summer too. Think I'll just throw them in with a hone and new rings/bearings

ok ok I will post both up when they come in

Some toys showed up today! :woowoo:

Wrinkle red painted the AAN vc... I hate it. Going to powder coat it instead :bashtard:


Let see, picked up some goodies from EFI express :-D, cam gear, springs from 034 and VDO gauges in a nice little costom pod for the interior. I think I will be needing a higher reading than 15psi on the boost though


Ash is excited


Just test fitting the guages :-D


Thats it for now.. more to come later this week :woowoo:

ohhh. thats some nice hardware!!! Very nice.

Damn, that manifold is hawttt I need something along those lines soon.

AHH! I want that! Where did you pick that up?

ohhh. thats some nice hardware!!! Very nice

I think so too

AHH! I want that! Where did you pick that up?

What part?

The IM man!

EFI Express, Talk to Marc Swanson or Hank (ShavedQuattro)

really good project

the RED wrinkle paint remind me something

good luck :wink:

the IM looks nasty,good prize too,its fit to 7At,isnt it?

Tom wrote:the IM looks nasty,good prize too,its fit to 7At,isnt it?

Ya I bet it would but I am not 100 percent sure.

Tom wrote:the IM looks nasty,good prize too,its fit to 7At,isnt it?

It fits, though realize that there is radiator ducts, a support going for the radiator and wiring that needs to be done. This is the case with any manifold that puts the inlet right there. They all require some trimming in the area, but are for the most part plug and play manifolds.

HTH

i read on Your site,that is need to used a shorter belt,but where i can find them?

It is not my site, but typically you can just go into the autoparts store with a belt and ask for a belt "x.x" inches smaller, and they will get you one. They fit with the factory belt, although it is very close. A half inch shorter belt makes the fit a tad better.

HTH

Nice, very seriously considering one of these. So... Any special deals for us motorgeekers?!

I am TOTALLY happy with the product. Looks sexy and is suppose to flow really really well. I don't know the exact numbers, either Marc or Hank will know. Plus it saves me from dealing with all the extra BS surrounding the radiator and routing the boost hoses in a big loop. Totally worth it in my opinion. :-D

:woowoo: :woowoo:

I am following this thread closely because I have an AAN that I will put into a 4k during the fall. Have you decided what you are going to do for engine management? :-)

I am planning on 034. I toyed with the idea of VEMS but where I am not a 200 or S4/S6 I decided against it. SO it's going to cost me big monies but it will be worth it for the reliablity where this will ultmatelly be my DD. :-D ... At this point I just hope to have it on the road before August

nice found it. good progress. like what you did to your lights. mixed feelings on the led mod on the older car but still cool. ellipsoids are dope