Aarons Drag CQ: 3-29 anodized and welded stuff. AN lines

speeding-g60 · Post by **speeding-g60** » Mon Jan 12, 2009 11:30 pm

well, its taken quite a bit, but i am this close to having the correct suspension under it again. and its in a bit of a different state from whence you owned it i think

i am looking to go pretty fast in it.

i faxed in the cage order sheet today. we shall see what they say.

i get the two VW's (both blown, one MK3 Vortech supercharged VR6, the other GT35R in a rabbit with 20v) ((and blown as in forced induction, not broken blown)) over to their new storage unit, and this car can get off the trailer and inside for some good lovin.....

windowlicker08 · Post by **windowlicker08** » Mon Jan 12, 2009 11:43 pm

i bought that car all flat black and running like s@#t.had plans for it.....but to many projects.when i get my done i'll have to make a visit and say hi.
:woowoo:

speeding-g60 · Post by **speeding-g60** » Thu Jan 15, 2009 3:26 pm

Twin disc. yeehaw.

i think this son of mine pretty much reflects my inner childs' feelings of joy with this stuff...

zerb · Post by **zerb** » Thu Jan 15, 2009 4:50 pm

Uber jealous.

derracuda · Post by **derracuda** » Thu Jan 15, 2009 10:41 pm

i wonder if those guys would make me some organic discs with the audi hubs for my 5.5" clutch :?

speeding-g60 · Post by **speeding-g60** » Sat Jan 17, 2009 4:25 pm

ok. one car gone, rabbit as soon as i re-plumb the coolant lines and switch back to 12 volt from 16 volt. nothing to it but to do it. then the coupe can come inside.

here is the new home of the vw's. i have lots of wheels and tires, i think i am somewhat of a packrat. i have them in the attic, the garage, the shed(s), the storage, outside the side of the house. most i will never use again. brand new BFG DR's, 2 x 205-50/15, 2 x 205-40/17. just junk laying around.

another bothersome thing is that i really like this car, the MK3, it is sooooo damned fun to drive as it is Vortech SC'd VR6. but i never have the time. i should sell it, but i will miss it if i do. its built.

Bilstein PSS-9's, BBS RK-II 2-pc wheels, bigger brakes, full audiophile level stereo setup, Quaife LSD, Momo, EIP manifold, all Autotech strut/sway bars, Techtonics/Borla exhaust, Rieger R-RX front end, ABT skirts/grill, Hella MK4-look HID lights, CF hood, and lots more. it is such a blast to drive. really is. also a pair of TSW Volcano rims and the 17" BFG DR's setup for if i ever wanted to drag it. run twice....

oh well. just a shot or two of it all cozy in its new home. i drove it three times last year i think.

speeding-g60 · Post by **speeding-g60** » Sat Jan 17, 2009 6:43 pm

and Spazz, the Pug dog of ours, is checkin it out. he COULD get sucked into it no prob.

derracuda · Post by **derracuda** » Sat Jan 17, 2009 7:11 pm

hey Aaron, check out the new eurotuner. there's coverage of the Pacific Waterland show and your rabbit in there with it's own caption

speeding-g60 · Post by **speeding-g60** » Sat Jan 17, 2009 7:27 pm

yeah i keep hearing that, but i have been to 5 places including two airports, and havent seen one. i even had the wife order tha online copies @ 3 bux each, but she got dec and jan. its the feb issue. i will get it soon enough

i will have someone meet me tomorrow @ airport to show it to me LOL.

and i got some more stuff done. here is exploded view of twin disc. and the rear bumper and skirts are painted now too. and there is nothing like a pile of spare parts.....

vagrant_mugen · Post by **vagrant_mugen** » Sat Jan 17, 2009 10:50 pm

very serious clutch setup there. i like that alot. very sexy, very tough. cant wait till i have enough power to warrant one....

whats the hold rating on that bitch???

and whats the deal with your oilpan? you going dry-sumpper for this car????

speeding-g60 · Post by **speeding-g60** » Sun Jan 18, 2009 4:43 am

oilpan is for buddy in Berlin.. cheaper for me to pick stuff up for him here and ship to him. and he, in return, gets me my stuff like the H4/H1 headlights for B4, etc.

it works out....

RSCoupe · Post by **RSCoupe** » Sun Jan 18, 2009 10:28 am

I like that exploded view of the clutch. Very cool. 8)

Post by **Hank** » Sun Jan 18, 2009 10:37 am

Cool clutch, and I dig the color dude.

RSCoupe · Post by **RSCoupe** » Sun Jan 18, 2009 10:49 am

Is that clutch setup basically an on/off switch?

speeding-g60 · Post by **speeding-g60** » Sun Jan 18, 2009 10:54 am

http://shop.dthaus.com/product.sc;jsess ... oductId=82 ... oductId=82

Deutsch Teile Haus is proud to offer Clutch Masters finest and most economical multi-plate clutch systems, the FX600 and FX700 Series. Clutch Masters' Twin Disc systems are pure racing technology that also works well in high performance street applications. They are designed to hold tremendous torque ratings, while retaining a very smooth operation. By using a smaller diameter clutch assembly, Clutch Masters Twin Disc systems have a reduced rotational mass, meaning quicker and smoother shifting and much better throttle response. By slightly increasing the clamping force of the pressure plate and adding to the square inches of usable disc area, CM Twin Discs significantly increase clamping values. The cover assembly is machined from billet aluminum with 25% more tensile strength than the competition's cast unit. They are available in three specific pressure ratings as well as several types of friction surfaces. The flywheel is machined from billet 6061-T6 aluminum to meet SFI spec 1.2 for competition in NHRA, NDRA, IDRC, IHRA, SCCA and NASA.

# Clutch Masters Twin Disc features: Components can be purchased separately for economical repair.
# Positive release for ease of high RPM staging and shifting.
# Most have experienced better 4/10's times and averaged hundreds of passes without complications or repair

# All systems include: Cover Assembly with attached Diaphragm
# Pressure Plate Ring
# Two Discs
# One Mid Plate
# Billet Aluminum or Steel Flywheel
# Release Bearing
# Pilot Bearing (when applicable)
# Pressure Plate Bolts

# Clutch Options: FX600 > Bonded Organic Kevlar mix for the street
# FX700 > Compressed Ceramic Bronze for the strip

# Flywheel Options: 8 lbs Billet Aluminum Flywheel (17 lbs total weight)
# 14 lbs Billet Steel Flywheel (23 lbs total weight)

*Billet Steel flywheel is exclusive to Deutsch Teile Haus

Average weight of the entire assembly is approximately 50% lighter than OEM.

speeding-g60 · Post by **speeding-g60** » Sun Jan 18, 2009 12:34 pm

and this color really is weird. in full sunlight, the copper effect metallic is really coming out. i cant wait until the whole thing is painted....

so should i do complete car? or still do the whole roof black?

RSCoupe · Post by **RSCoupe** » Sun Jan 18, 2009 1:05 pm

Do the whole car the copper color. You should also do the bottom part of the rear bumper since with the side skirts, the black doesn't line up with, or relate to, anything any more.

speeding-g60 · Post by **speeding-g60** » Sun Jan 18, 2009 1:31 pm

hmmm. i think you got it there with the bumper. but it sucks to paint the textured section of it. i guess we just have to sand the crap out of it to make it stick... prep it right.

but the bumper is done, he's gonna be pissed when i ask him to paint the whole thing HAHA

but that color.... look further up the page you will see it in less light, looks way different. its strange.

Post by **HT Motorsport** » Sun Jan 18, 2009 3:20 pm

Painting the textured part of the bumper would work fine, you nee dot do some special prep and use special paint and additives, but it works fine. BTDT, Ill did out some pics and info if I can fined em....

derracuda · Post by **derracuda** » Sun Jan 18, 2009 4:01 pm

i say do the whole car in the same color.. not monochromatic though. it's not an american hotrod. german cars have beltlines for good reason.

SilverCQ · Post by **SilverCQ** » Sun Jan 18, 2009 4:35 pm

i say do the whole car...that color looks sweet

Post by **HT Motorsport** » Sun Jan 18, 2009 5:23 pm

I say black roof (Just cos I wanna see how it looks)

Wait..... Scratch that, go ahead and paint the whole car, then get the roof gloss black wrapped to see if you like it all one color first.

speeding-g60 · Post by **speeding-g60** » Sun Jan 18, 2009 5:29 pm

picture a Gen 1 mitsu eclipse.... that type of theory... the only down side is that big expanse on the hatch pillar. it would look great with dark tinted windows, but i dont run tint on the strip.... its all just planing. and he took the rear lower bumper repaint rather wel actually. i had to stroke his ego some, and tell him that his idea (which was the whole thing) in the first place was better. so i think when i go home next wekend, doors will be done as well.

Derek, please expand on this "beltline" is that the door trim?

Alloutofdonuts · Post by **Alloutofdonuts** » Sun Jan 18, 2009 5:29 pm

I guess it was the combination of the pug and the huge turbo but that cracks me up. Did Spazz do that to your sweat pants??

That color is the same the front of the car is painted? Almost looks maroon in the other pics if it's the same. But that color orange-ish is

what I was going to paint my old turbo rabbit, but ended up painting it a pinkish maroon(porsche color

)

speeding-g60 · Post by **speeding-g60** » Sun Jan 18, 2009 5:37 pm

yeah, its the same color, same paint. its weird.. but real cool looking...

and no, Spaz didnt do the sweats. many hours of building the rabbit.... welding, grinding....

Aarons Drag CQ: 3-29 anodized and welded stuff. AN lines

really like this color....